API Spec 5CT P110 Oil Casing Pipe Coupling Joint Petroleum Well Pipe Tubing Casing Drill Well Seamless Steel Pipe Oil CasingTube
Sample free!
- Satisfaction Guaranteed
- No Hassle Refunds
- Secure Payments
API 5CT P110 casing Tubing Specification
P110 API casing or tubing is a relatively common one in oil drilling. Because of the low steel Grade of P110, it is used for shallow Oil and Gas extraction. Due to its low Price among other grades of steel, it enjoys broader applications. P110 API casing or tubing is widely used in the extraction of natural gas and coalbed methane, and can be commonly found in shallow wells, geothermal wells, and water wells.
api 5ct p110 Casing Tubing Type of Casing:
- short round Thread casing(SC)
- long round thread casing(LC)
- buttress thread casing(BC)
API 5CT P110 Casing Tubing Chemical Composition:
Chemical Composition, Mass Fraction (%) | ||||||||||||||
Grade | C | Mn | Mo | Cr | Ni | Cu | P | S | Si | |||||
Type | min | max | min | max | min | max | min | max | max | max | max | max | max | |
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 |
H40 | — | — | — | — | — | — | — | — | — | — | — | — | 0.03 | — |
J55 | — | — | — | — | — | — | — | — | — | — | — | — | 0.03 | — |
K55 | — | — | — | — | — | — | — | — | — | — | — | — | 0.03 | — |
N80 | 1 | — | — | — | — | — | — | — | — | — | — | 0.03 | 0.03 | — |
N80 | Q | — | — | — | — | — | — | — | — | — | — | 0.03 | 0.03 | — |
R95 | — | — | 0.45 c | — | 1.9 | — | — | — | — | — | — | 0.03 | 0.03 | 0.45 |
l80 | 1 | — | 0.43 a | — | 1.9 | — | — | — | — | 0.25 | 0.35 | 0.03 | 0.03 | 0.45 |
L80 | 9Cr | — | 0.15 | 0.3 | 0.6 | 0.9 | 1.1 | 8 | 10 | 0.5 | 0.25 | 0.02 | 0.03 | 1 |
L80 | 13Cr | 0.15 | 0.22 | 0.25 | 1 | — | — | 12 | 14 | 0.5 | 0.25 | 0.02 | 0.03 | 1 |
C90 | 1 | — | 0.35 | — | 1.2 | 0.25 b | 0.85 | — | 1.5 | 0.99 | — | 0.02 | 0.03 | — |
T95 | 1 | — | 0.35 | — | 1.2 | 0.25 b | 0.85 | 0.4 | 1.5 | 0.99 | — | 0.02 | 0.03 | — |
C110 | — | — | 0.35 | — | 1.2 | 0.25 | 1 | 0.4 | 1.5 | 0.99 | — | 0.02 | 0.03 | — |
P110 | e | — | — | — | — | — | — | — | — | — | — | 0.030 e | 0.030 e | — |
Q125 | 1 | — | 0.35 | 1.35 | — | 0.85 | — | 1.5 | 0.99 | — | 0.02 | 0.01 | — | |
NOTE Elements shown shall be reported in product analysis. | ||||||||||||||
a The carbon content for L80 may be increased up to 0.50 % maximum if the product is oil-quenched or polymer-quenched. | ||||||||||||||
b The molybdenum content for Grade C90 Type 1 has no minimum tolerance if the wall thickness is less than 17.78 mm. | ||||||||||||||
c The carbon content for R95 may be increased up to 0.55 % maximum if the product is oil-quenched. | ||||||||||||||
d The molybdenum content for T95 Type 1 may be decreased to 0.15 % minimum if the wall thickness is less than 17.78 mm. | ||||||||||||||
e For EW Grade P110, the phosphorus content shall be 0.020 % maximum and the sulfur content 0.010 % maximum. |
API 5CT P110 Casing Tubing Mechanical Properties:
Tensile and Hardness Requirements | |||||||||
Grade | Yield Strength MPa | Tensile Strength | Hardness a,c | Specified Wall Thickness | Allowable Hardness Variation b | ||||
Type | Total Elongation Under Load | min MPa | max | ||||||
min | max | HRC | HBW | mm | HRC | ||||
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 |
H40 | — | 0.5 | 276 | 552 | 414 | — | — | — | — |
J55 | — | 0.5 | 379 | 552 | 517 | — | — | — | — |
K55 | — | 0.5 | 379 | 552 | 655 | — | — | — | — |
N80 | 1 | 0.5 | 552 | 758 | 689 | — | — | — | — |
N80 | Q | 0.5 | 552 | 758 | 689 | — | — | — | — |
R95 | — | 0.5 | 655 | 758 | 724 | — | — | — | — |
L80 L80 | 1 | 0.5 | 552 | 655 | 655 | 23 | 241 | — | — |
L80 | 9Cr 13Cr | 0.5 | 552 | 655 | 655 | 23 | 241 | — | — |
0.5 | 552 | 655 | 655 | 23 | 241 | — | — | ||
C90 | 1 | 0.5 | 621 | 724 | 689 | 25.4 | 255 | £12.70 | 3 |
12.71 to 19.04 | 4 | ||||||||
19.05 to 25.39 | 5 | ||||||||
³ 25.40 | 6 | ||||||||
T95 | 1 | 0.5 | 655 | 758 | 724 | 25.4 | 255 | £12.70 | 3 |
12.71 to 19.04 | 4 | ||||||||
19.05 to 25.39 | 5 | ||||||||
³ 25.40 | 6 | ||||||||
C110 | — | 0.7 | 758 | 828 | 793 | 30 | 286 | £12.70 | 3 |
12.71 to 19.04 | 4 | ||||||||
19.05 to 25.39 | 5 | ||||||||
³ 25.40 | 6 | ||||||||
P110 | — | 0.6 | 758 | 965 | 862 | — | — | — | — |
Q125 | 1 | 0.65 | 862 | 1034 | 931 | b | — | £12.70 | 3 |
12.71 to 19.04 19.05 | 4 | ||||||||
5 | |||||||||
a In case of dispute, laboratory Rockwell C hardness testing shall be used as the referee method. | |||||||||
b No hardness limits are specified, but the maximum variation is restricted as a manufacturing control in accordance with 7.8 and 7.9. | |||||||||
c For through-wall hardness tests of Grades L80 (all types), C90, T95 and C110, the requirements stated in HRC scale are for maximum mean hardness number. |
API 5CT P110 Casing Tubing Range Lengths | |||
Range 1 | Range 2 | Range 3 | |
CASING (PE/T and C/SF) | |||
Total range length, inclusive Permissible variation, max a | 4.88 to 7.62 1.83 | 7.62 to 10.36 | 10.36 to 14.63 1.83 |
1.52 | |||
tubing and casing USED AS TUBING | |||
(PE/T and C/SF) | |||
Total range length, inclusive Permissible variation, max a | 6.10 to 7.32 b | 8.53 to 9.75 c | 11.58 to 12.80 d |
0.61 | 0.61 | 0.61 | |
INTEGRAL TUBING CONNECTIONS (including IJ/PE | |||
and IJ/SF) | |||
Total range length, inclusive Permissible variation, max a | 6.10 to 7.92 e | 8.53 to 10.36 | 11.58 to 13.72 0.61 |
0.61 | 0.61 | ||
PUP JOINTS | Lengths: 0.61; 0.91; 1.22; 1.83; 2.44; 3.05 and 3.66 e | ||
Tolerance: ±0.076 | |||
a Length variation applies to rail car shipment to the point of use and does not apply to order items of less than 18,144 kg of Pipe. | |||
b By agreement between purchaser and Manufacturer, the maximum length may be increased to 8.57 m. | |||
c By agreement between purchaser and manufacturer, the maximum length may be increased to 10.76 m. | |||
d By agreement between purchaser and manufacturer, the maximum length may be increased to 17.72 m.0.61 m pup joints may be furnished up to 0.91 m long by agreement between purchaser and manufacturer, and lengths other than those listed may be furnished by agreement between purchaser and manufacturer. |